Philippe Freycon Décoration
Le plafond tendu BARRISOL > Fiche technique

Fiche technique

Pour le particulier

Le plafond tendu est une toile en PVC sur mesure (aux formes exactes de la pièce) ; elle est bordée d’un joint (ou harpon). Le technicien la chauffe à l’aide d’un canon à chaleur, pour la tendre et l’enclencher dans les lisses périphériques ( baguettes fixées sur le pourtour des murs).

Les luminaires existants ou des spots, spécialement conçus pour éviter la surchauffe de la toile, peuvent être placés dans le plafond tendu.

Intégration possible aussi d’éléments techniques : VMC, climatiseur,...

Pour le prescripteur

Dans les locaux en construction, la pose des plafonds se fait uniquement dans des bâtiments hors air, hors eau et hors poussière.

Le plénum doit être étanche à l’air à 100 %.

Les éléments d’isolation posés dans le plénum auront au minimum un classement au feu M1 (ininflammables).

Les caissons de volets roulants doivent être étanches à l’air.

Les plafonds sont fabriqués sur mesure en usine, des adaptations et finitions peuvent être nécessaires lors de la pose.

Les transformateurs des spots sont généralement fixés directement au plafond existant ou sur des murs. Le Barrispot est conformé pour recevoir le transformateur qui peut être atteint à la main sans décrocher le plafond tendu.

Les spots encastrés orientables sont généralement compatibles avec BARRISOL. Lorsque la chaleur qu’ils diffusent est supérieure à 50°C, il est obligatoire de placer une rondelle isolante entre la rosace du spot et la toile BARRISOL. La puissance des spots ne doit pas être supérieure à 50W. Les spots qui transmettent à leur rosace métallique plus de 60°C sont incompatibles avec les plafonds BARRISOL, même équipés de rondelles isolantes.

En cas de ventilation mécanique, les flux d’entrée et d’extraction d’air doivent être correctement dimensionnés pour être équilibrés.

Technical card-index

For the private individual

The stretched ceiling is a PVC fabric made to measure (with the exact shapes of the room) ; it is bordered with a joint (or harpoon). The technician heats the fabric using a heat, and then the fabric is tightened onto the circumference of the walls using "rods" (or "lisses"). The existing spotlights or lamps are especially designed to avoid the overheating of the fabric, and can be installed in the stretched ceiling. It is also possible to install other technical elements such as : hood, chimney, air-conditioner...

For the prescriber(designer/installer)

In the building, the installation of the ceilings is done only in buildings away from air draughts, water and dust.

The "plenum" must be tight with the air to 100 %. The elements of insulation posed in the plenum will have at least a classification of "fire M1" standard (non flammable).

The boxes of travelling shutters must be tight with the air.

The ceilings are manufactured to measure in factory, and any modifications necessary are made during the installation.

The transformers of the spots are generally fixed directly at the existing ceiling or on walls. Barrispot is formed to receive the transformer which is accessible without the need of taking down the stretched ceiling.

The directional embedded spots are generally compatible with the BARRISOL brand fabric. When the heat that they diffuse is higher than 50°C, it is obligatory to place an insulating disc between the rosette of the spot and the fabric.

The power of the spots should not be higher than 50W. The spots which transmit to their metal rosette more 60°C are incompatible with ceilings, even those equipped with insulating discs.

In the event of mechanical ventilation, flows of entry and extraction of air must be correctly sized to be balanced.